OMNIO - Blind actuator 1-channel UPJ230/12

Presentation

The Omnio flush mounted multi blind actuator 1-channel UPJ230/12 is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its two potential free interlocked outputs are able to regulate one drive and can be actuated from up to 30 Omnio radio transmitters. This allows the exact positioning of the blinds and the slats. Further features are monitoring of window and sliding doors, automatic functions for temperature- wind- and rain sensors and positioning functions including feedback to higher-level systems or visualisations. Bidirectional communication, EnOcean Equipment Profile (EEP) D2-05-00. Suitable for flush- or surface mounted sockets. ARCO ready (AWAG Remote Commissioning). 

Product Description

The Omnio flush mounted multi blind actuator 1-channel UPJ230/12 is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors. Its two potential free interlocked outputs are able to regulate a drive and be controlled by up to 50 Omnio radio transmitters. This allows the exact positioning of blinds and slats. Further features are window and sliding door surveillance, indoor temperature controlled automatic mode, connection of an Omnio weather station XFJ, positioning functions and feedback for higher-level control and visualisation. Bidirectional communication, EEP D2-05-00, ARCO ready (AWAG Remote Commissioning). In addition, this actuator can be used as repeater in case of range issues. Suitable for flush mounted sockets.

FUNCTIONS

• Controls 230 V~ tubular motors of blinds, sun blinds, awnings, sliding gates or garage doors • Slat angle settings •
• Controlled by handheld or wall mounted transmitters •
• Window and sliding door surveillance •
• Indoor temperature controlled automatic mode with Omnio sensor RTF •
• Automatic mode for wind, sun and rain in conjunction with an Omnio weather station •
• Manual/automatic change over with handheld or wall mounted transmitter or key-card switch •
• Positioning functions and feedback for higher-level control and visualisation •
• Repeater function • EnOcean Equipment Profile (EEP) D2-05-00 •
• ARCO ready (AWAG Remote Commissioning)

General

The Omnio actuators (receivers) are controlled by radio signals coming from the Omnio transmitters. Each transmitter is able to control an unlimited number of actuators. The radio transmitter can be manually programmed and deprogrammed to an actuator following a simple procedure. Via actuator each transmitter can be given a certain function and different parameters. With ARCO technology, all Omnio actuators can be configured completely by radio without manual access to the device. The powerful software E-Tool constitutes the key component for conveniently planning, configuring and documenting projects of any size right at your desk. 

technical specifications

• Voltage supply: 110-240 V~ 50/60 Hz
• Standby-power consumption: < 1 W
• Hardware protection (automatic circuit breaker / fuse): 13 A
• Power output
• Switch contact:2 interlocked isolated closing contacts
• Rated current: 6 A / 240 V~
• Maximum inrush current: 10 A
• Rated load AC1: 1500 VA
• Rated load  AC15 (230 V~): 300 VA
• Single phase motor rating AC3 (230 V~): 185 W
• Fluoreszenzlampen (cosφ = 0.9, C = 140 µF): not suitable
• Screw terminals: 4 mm²
• Protection class: IP20
• Overvoltage protection: Yes
• Permanently shortcircuit proof (control unit): Yes
• Technology: EnOcean 868 MHz
• Radio module: EnOcean TCM320 bidirektional / bidirectionnel M
• EnOcean Equipment Profile (EEP) : 
• Environment: -20 … +40 °C / 5 ... 90 % rH non condensing E
• Housing: Lexan, ø 51 x 25 mm
• Weight: 45g
• EC-Directives: 2006/95/EC, 2004/108/EC
• Standards: EN 60669-1/-2-1/-2-2, EN 61000-3-2/-3-3, EN 62493