HELTUN - Z-Wave Relay Switch quinto (5 channel) HE-RS01

TAKE CONTROL

​

For example, you can control up to...

• Five ON/OFF devices
• Three ON/OFF devices, and one, two-direction motor
• One ON/OFF device, and two, two-direction motors

At 26mm in depth, the Relay Switch quinto is also ‘impossibly small’, fitting into any rectangular, round or square electrical junction box, even behind attached devices.

INPUTS, OUTPUTS & SENSORS

The main power input can be either 85-265VAC or 12-48VDC. There are five relay outputs each with a maximum 5 Amp load. There are also two independent inputs for relay channels which allow control of systems with different power sources, or to use outputs as dry contacts: e.g. to switch ON/OFF 220VAC lights and control motorized valves with 24VDC power.

There are six pilot wire inputs: one common and five for each relay channel. This allows the Relay Switch quinto to be controlled by up to five different sources (e.g. five different light switches) and control all relay outputs separately. Each relay channel uses the HELTUN Advanced Zero-Cross Technology to deliver greatly increased longevity & reliability.

KNOW HOW MUCH ENERGY YOU USE

POWERFULLY CUSTOMIZABLE

There are seven different modes that can be selected for the Relay Switch quinto with up to five pilot wires being used to control any relay output to devices like a wall switch, alarm panel, etc.

• Invert State - If ON, turn OFF when pilot wire circuit is closed (or if OFF, switch ON).
• Momentary - Switch ON when pilot wire circuit is closed, switch OFF when opened.
• Momentary Reversed - Switch OFF when pilot wire circuit is opened, switch ON when closed.
• Switch ON Only - When the pilot wire circuit is closed (i.e. short-circuited).
• Switch OFF Only - When the pilot wire circuit is closed (i.e. short-circuited).

The Relay Switch quinto output can also be controlled by an internal timer. For example, after the switch is turned ON, it can be configured to automatically switch OFF a specified time later (or vice-versa: turn ON after being turned OFF). This function can be used to open or close garage doors, gates, blinds, curtains, locks, etc., and then return them to their previous state with no additional input.

• Timer (ON then OFF) - Switch ON when pilot wire circuit is closed, then Switch OFF after specified time.
• Timer (OFF then ON) - Switch OFF when pilot wire circuit is closed, then Switch ON after specified time.

MOTORIZED DEVICE CONTROLS

SCHEDULES & SCENARIOS

MAKE CIRCUIT BREAKERS SMART

EASY TO INStall

The HELTUN High Load Switch can be easily installed into any standard electrical junction box (rectangular, square, or round) in just minutes. Installation must only be performed by someone trained in handling high voltage electrical systems.

Z-WAVE PLUS V2 (700) COMPATIBLE

You can connect HELTUN devices to a Smart Home controller using the latest Z-Wave Plus V2 700 platform. HELTUN features advanced Smart Start technology for easy system integration, and the Security 2 (S2) framework with AES 256 encryption for safe data transfer.
 

This Relay Switch is compatible with all Z-Wave certified controllers and devices that properly implement Z-Wave switch classes. Using a Z-Wave controller, you can manage all switch functions via a mobile app including relays state changes, viewing energy consumption charts, and much more.
 

Up to 15 separate devices can be connected to your HELTUN Relay Switch quinto. You can associate it with any Z-Wave compatible ON/OFF switch, or other Switch, to control different systems in a room. You can even connect motion sensors and change the switch modes when people are detected in the house.

HELTUN devices are compatible with all Z-Wave frequencies for different countries (Europe, Russia, Israel, Australia, USA, India, Hong Kong, China, Japan, and Korea). The full list of Z-Wave regions and frequencies is available at Z-Wave Global Regions SiLabs page.

HELTUN periodically releases new device firmware with added features which can be remotely updated via an encrypted OTA (Over-The-Air) process.

FONCTIONS

• Options for Inclusion/exclusion to/from Z-Wave network
  • Non-Secure
  • S0 Secure
  • S2 Unauthorized, S2 Authorized with Key
• Association control of 50 devices from network
• Motorized device control (roller shutter mode)
• Schedule Mode
• Each of the five pilot wires inputs can control any relay output
• Up to five outputs can be controlled by one pilot wire
• Seven modes for each relay output:
  • Invert State (ON to OFF or OFF to ON)
  • Momentary (ON when shorted, OFF when released)
  • Momentary Reversed (OFF when shorted, ON when released)
  • Switch ON Only
  • Switch OFF Only
  • Timer (ON then OFF after specified time)
  • Timer (OFF then ON after specified time)
• Each relay outputs can be managed by Z-Wave gateway or associated device
• Each pilot wire can trigger scenes
• Power consumption software logic
• Factory reset button
• OTA (Over-The-Air) firmware update

TECHNICAL SPECIFICATIONS

• Dimensions: 50x50x26mm
• Material: Flame retardant plastic
• Color: White
• Five relays for resistive loads up to 5A each
• Two independent relay inputs (dry contact)
• Relay switching with HELTUN Advanced Zero-Cross Technology
• One common (S) and five pilot wires (S1, S2, S3, S4, S5) for external control
• Energy consumption software logic
• Operating temperature: 0°С to +60°С
• Power supply: 85-265VAC 50Hz/60Hz, or 24-48VDC
• Power consumption: <1W
• IP class: IP21
• Z-Wave Plus V2 SDK: V7.11
• Z-Wave module: ZGM130S
• Mounting – either:
• Flush electrical junction box:
  • round, rectangular or square type – min. depth 40mm
    • Optional adapter for DIN Rail mounting (50mm width) or on wall screwing