The Heltun HT-01 Thermostat is a programmable room thermostat with an LCD screen, four touch buttons and several sensors (temperature, humidity, brightness) for optimal control of your heating. It is recommended to control electric heaters, boilers, heating mats or underfloor heating. Its 16A relay allows it to switch large loads.
Attention: choose the color from the drop-down list below.
The Heltun HT-01 Thermostat is a programmable room thermostat with an LCD screen, four touch buttons and several sensors (temperature, humidity, brightness) for optimal control of your heating. It is recommended to control electric heaters, boilers, heating mats or underfloor heating. Its 16A relay allows it to switch large loads.
When considering thermal comfort, what aspects are the most important?
Is it general room temperature? Heating or cooling temperature? Conditioning or ventilation speed?
Or may be something else? Whatever the need, HELTUN guarantees to take care of it.
Powerful, efficient and well-designed, HELTUN is the thinnest and most stylish thermostat on the market.
Its fire and short circuit resistant plastic casing is only 9mm thick.
HELTUN thermostat integrates seamlessly into your interior design and is available in 30 combinations:
5 frames (silver, chrome, white, gloss and matte black) and 6 glass types (white, black, yellow, green, red, blue)
When an electronic device carries out its function, a certain amount of heat is generated. As a result, the ambient temperature is usually reported incorrectly, with merely a 1.5-2.0 degrees Celsius precision. HELTUN engineers added two additional internal sensors that consider excess heat generated from the device itself, whilst a special compensating software calculates the ambient temperature with an incredible 0.2-0.3 degrees Celsius precision.
The HELTUN Fan Coil Thermostat has 5 relay outputs each with max 5A load and two independent inputs for relay channels which allow it to control systems with different power sources for Fan Speed and heating/cooling control. It is possible or to use outputs as dry contacts. E.g. to
Input 1 with the required power source is for relay channels 1, 2 and 3, which can be loaded up to a max 15A and used for fan speed control.
Input 2 with the required power source is for relay channels 4 and 5, which can be loaded up to a max 10A and used for heating/cooling control.
With our built-in power consumption software logic you can monitor precisely how much energy was used during any particular day, week or month.
Just specify the consumption of the load in watts for each relay channel and the special logic will calculate total consumption relatively to the time since the output is in the ON state.
HELTUN touch buttons are so sensitive that they react even before you physically touch them, processing the action at a 1-2mm distance. The buttons are:
HELTUN’s large LCD screen shows all the necessary information simultaneously and does not require any additional commands to access it.
There is an instant access to information from all sensors: ambient room temperature, air humidity, current temperature settings, thermostat’s operating mode, climate mode, fan speed, date and time.
Automatic screen brightness control seamlessly adjusts to the ambient light conditions, making it easy to read even in the dark.
COM and ECO modes constantly maintain the set temperature. The user can easily change the temperature set for each mode. To do this, simply press the "Mode" button to select the desired mode, and use the "+" and "-" buttons to set the required temperature.
TIME mode allows to set a different temperature for Morning, Day, Evening and Night period for each 7 days of the week.
In Heating & Cooling mode the thermostat will constantly maintain the desired temperature. If the ambient room temperature will be higher than the Set Temperature the device will go to the Cooling state. In case the room temperature drops the thermostat will go to the Heating state.
In Heating only mode the thermostat will go to Heating state if the ambient room temperature will be lower than the Set Temperature and will go to IDLE state if the room temperature is higher than that required.
In Cooling only mode the thermostat will go to Cooling state if the ambient room temperature will be higher than the Set Temperature and will go to IDLE state if the room temperature is lower than required.
In Ventilation mode the thermostat will only ventilate.
Reduce your power bill by up to 50% and help look after the environment by activating the TIME mode.
Adjust home temperature according to your habits by reducing it while you are away from home and increasing in the evenings and early mornings.
On average, people spend about 12-14 hours a day at home. The rest of the time the house is empty and only needs minimum heating. Consider 7/8 hours of sleeping time in the hours spent at home, keeping in mind that the optimal sleeping temperature is considered to be 18 degrees Celsius.
The thermostat can be set individually for morning, day, evening, night. For example, it can be assigned for Monday morning start at 7.00, then day temperature starting at 9.00 (when absent for work etc.), then evening starting at 18:00 (half an hour before occupants return). The night regime then begins at 23.30 (bedtime).
You can have separate temperature settings for all 4 periods. But this is not all; as temperature can be programmed for each day of the week, weekends can be handled differently.
Fan Speed (heating, cooling or ventilation power) can be controlled manually or in Auto mode.
There are 4 speed levels – Off, Low, Medium, High.
In Auto mode the thermostat logic will automatically select the speed level regarding the difference of the desired temperature and ambient room temperature.
When the ambient room temperature reaches the required temperature, the thermostat will go to IDLE (fan off) state.
Hysteresis defines when the system should switch the heating on or off when temperature changes. For example, if the desired temperature is 25 degrees Celsius and hysteresis value is set to 0.5 degrees, it will switch the heating on when ambient temperature drops to 24.5 degrees Celsius.
The higher your hysteresis value is set, the more energy you can save but at the same time the variations in your room temperature will be higher. The factory default is 0.5 degrees.
In case of a power cut or disconnection from the main power source, internal memory is not erased – once you switch the device back on, all your saved settings will be fully functional.
To prevent children from meddling with your thermostat settings, you can activate the special child-safe mode.
HELTUN devices can be easily installed into any standard wall socket (rectangular or round type).
You can connect HELTUN devices to a Smart Home gateway/controller using the latest Z-Wave Plus V2 700 platform. HELTUN features advanced Smart Start technology for easy system integration, and the Security 2 (S2) framework with AES 256 encryption for safe data transfer.
This thermostat is compatible with all Z-Wave certified controllers and devices that properly implement Z-Wave thermostat classes. Using a Z-Wave controller, you can manage all thermostat functions via a mobile application including temperature and mode changes, viewing accurate energy consumption charts, and much more.
Up to 5 separate devices can be connected to your HELTUN thermostat. You can associate it with any Z-Wave compatible ON/OFF switch, or other thermostat, to control different climate systems in a room. You can even connect motion sensors and change thermostat modes when people are detected in the house.
HELTUN devices are compatible with all Z-Wave frequencies for different countries (Europe, Russia, Israel, Australia, USA, India, Hong Kong, China, Japan, and Korea). The full list of Z-Wave regions and frequencies is available at Z-Wave Global Regions SiLabs page.
The correct frequency can be selected in the device menu.
HELTUN periodically releases new firmware with additional features and functionality which can be sent to devices via an encrypted OTA (Over-The-Air) update process.
Heltun is a manufacturer specialized in Z-Wave wireless home automation. Designed and developed in Armenia, Heltun products offer a very high quality design and finish.
Domo-Supply/Swiss-Domotique is Heltun's general importer for Switzerland.
