Qubino - Z-Wave+ Flush on/off thermostat ZMNHID1

The Z-Wave PLUS ZMNHID1 module from Qubino enables an accurate management of your heating based on the temperature measured by the sensor supplied.

This all-in-one pack includes a compact Qubino module and a temperature sensor. The flush-fitting Qubino module in this set acts as a thermostat via a series of special parameters.

The kit enables you to control a thermostatic system via your home automation box. The module will itself control your heating according to the instructions you supply. Then, based on the temperature measured by the sensor, the module will adjust the functioning of the heating system so that it meets the required temperature.

You can choose one of two different modes: Auto and Off

• In Auto mode, the module will control the device connected to its output to meet the thermostat instruction that has been remotely set.
• In Off mode the device linked to the output will be switched in order to lower the room temperature (down to an adjustable minimum temperature limit).

The module features a number of different configurable functions:

• The temperature instruction can be sent via the Z-Wave controller.
• Choice of output control type: the output relay can be configured appropriately according to whether the module is connected to the heating supply (NO), or to a pilot wire input where On and Off are reversed (NC). Similarly, you can control your air conditioning, switching it on or off.
• Upper and lower hysteresis: defines the minimum temperature difference between the set temperature and the measured temperature for the module to then switch the heating on or off accordingly.
• Frost free mode: Specifies a minimum temperature for the heating system connected to the module. By activating this instruction, your heating will never drop below the temperature specified and prevent your pipes from freezing.

By adjusting the module output to operate as NC, you can connect it to the pilot wire input of a heater using a diode pilot wire and thus control the "Comfort" and "Off" settings of the heating.

Installation is extremely simple and enables you to connect up to 3 different switches (one to select the Auto or Off mode and 2 switches or external wired sensors that provide information from the Z-Wave groups associated with the module). You can connect the module in 230VAC (required if using the pilot wire) or 24VDC.

This an economical and environmentally-friendly module: consuming less than 0.4W, it also continuously measures the energy used at any given moment (in Watts) and the total consumption (in kWh) of the device it controls. The power consumed by these devices can therefore be recovered from your home-automation box, giving you a detailed overview of your energy consumption.

Finally, it should be noted that the QUBINO brand has set itself demanding quality and sustainability targets: for this reason they have selected high-performance components such as the OMRON relay. The numerous quality control tests carried out on the module ensure maximum durability (tough enough to operate at temperatures ranging from -10°C to 40°C).

Features

• Remote control for heating
• Fits behind an existing switch
• Thermostat function
• A casing specifically designed for easy installation (simple cable fixings), tested by professional electricians
• Integrates a 500 series Z-Wave chip
• Communication 250% faster compared to standard Z-Wave devices
• Optimised radio range
• Very low power consumption, less than 0.4W
• Operating temperature of -10 to 40˚C
• Analogue temperature sensor included
• Temperature measurement to 0.1°C
• 2 binary inputs enable the connection of additional devices such as sensors, push or bistable buttons, etc.
• Use to directly control a water or electric underfloor heating system, boiler, hot water pump, electric heater, etc.

Technical specifications

• Power supply: 110 - 230 VAC ±10% 50/60Hz, 24-30VDC
• Power Consumption: 0.4W
• Rated load current of AC output (resistive load): 1 X 10A / 230VAC
• Rated load current of DC output (resistive load): 1 X 10A / 30VDC
• Power circuit AC output (resistive load): 2300W (230VAC)
• Power circuit DC output (resistive load): 240W (24VDC)
• Power monitoring accuracy: P=5-50W, +/-3W ; P>50W, +/-3%
• Radio frequency: 868.42MHz, Z-Wave
• Range: up to 30m indoors (depending on surrounding material)
• Digital temperature sensor measurement range: -50 ~ 125°C
• Operating temperature: -10 ~ 40°C
• Space required for installation: Ø ≥ 60mm
• Dimensions (L x H x D): 41.8 x 36.8 x 15.4mm
• Weight: 25g
• Temperature range of the digital sensor: -50.0 ~ 125.0°C
• Resolution: 0.1°C
• Length of temperature sensor cable: 1000 mm
• Certifications: EC, RoHs